Сообщений в теме: 2

[getAway]

киа рио 2 (JB)

Kia Rio JB (2006-2009) - снятие и установка радиатора кондиционера

REPLACEMENT CONDENSER ASSEMBLY 1. Recover the refrigerant with a recovery/ recycling/ charging station (Refer to HA-9). 2. Disconnect the negative (-) battery terminal. 3. Remove the radiator. (Refer to EM group - Radiator) 4. Remove 2 nuts (A), and then disconnect the discharge line and liquid line from the condenser. Plug or cap the lines immediately after disconnecting them to avoid moisture and dust contamination. TORQUE: 7.8~11.7N.m (0.8~1.2kgf.m, 5.9~8.7lb.ft)  1 copy.jpg   33.45К   11 Количество загрузок: 5. Remove 2 bolts, and then remove the condenser (A) by lifting it up. Be careful not to damage the radiator and condenser fins when removing the condenser.  2 copy.jpg   46.69К   15 Количество загрузок: 6. Install in the reverse order of removal, and note these items : A. If you're installing a new condenser, add refrigerant oil ND-OIL8. B. Replace the O-rings with new ones at each fitting, and apply a thin coat of refrigerant oil before installing them. Be sure to use the right O-rings for R-134a to avoid leakage. C. Be careful not to damage the radiator and condenser fins when installing the condenser. D. Be sure to install the lower mount cushions of condenser securely into the holes. E. Charge the system, and test its performance. (Refer to HA-10) DESICCANT 1. Remove the condenser, and then remove the bottom cap (B) with L wrench (A) from the condenser. TORQUE: 20~25N.m (2.0~2.5kgf·m, 14.5~18.2lb-ft)  3 copy.jpg   22.75К   12 Количество загрузок: 2. Remove the desiccant (A) from condenser using a long nose plier. Check for crumbled desiccant and clogged bottom cap filter.  4 copy.jpg   22.28К   12 Количество загрузок: 3. Apply air conditioning compressor oil along the O-rings and threads of the new bottom cap. 4. Insert the new desiccant into the receiver drier tank. The desiccant must be sealed in vacuum before it is exposed to air for use. 5. Install the new bottom cap to the condenser. - Always replace the desiccant and bottom cap at the same time. - Replace the O-rings with new ones at each fitting, and apply a thin coat of refrigerant oil before installing them. Be sure to use the right O-rings for R-134a to avoid leakage. - Be careful not to damage the radiator and condenser fins when installing the condenser. - Be sure to install the lower mount cushions of condenser securely into the holes. - Charge the system, and test its performance. (Refer to HA-10)

[getAway]

Kia Rio JB (2006-2009) - снятие и установка компрессора кондиционера

REMOVAL 1. If the compressor is marginally operable, run the engine at idle speed, and let the air conditioning work for a few minutes, then shut the engine off. 2. Disconnect the negative cable from the battery. 3. Recover the refrigerant with a recovery/charging station (Refer to HA-9). 4. Loosen the drive belt (Refer to HA-15). 5. Remove the bolts, then disconnect the suction line (A) and discharge line (B) from the compressor. Plug © or cap the lines immediately after disconnecting them to avoid moisture and dust contamination.  1 copy.jpg   32.74К   9 Количество загрузок: 6. Disconnect the compressor clutch connector (A), and then remove 4 mounting bolts and the compressor.  2 copy.jpg   31К   9 Количество загрузок:

[getAway]

INSTALLATION

<table border="0" cellpadding="0" cellspacing="0" style="width:100%;padding-bottom:6;"> <tbody> <tr> <td style="padding-left:3px;" valign="top" width="12"> 1.</td> <td style="padding-left:3px;" valign="top">
Make sure of the length of compressor mounting bolts, and then tighten it A?B?C?D order. <table border="1" cellpadding="3" cellspacing="0" style="border:solid 1pt gray;BORDER-COLLAPSE: collapse;bgcolor=#ccffff;width:100%;MARGIN-top: 5px;"> <tbody> <tr> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="20%%"> Bolt</td> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="40%%"> ? Engine (1.4, 1.6)</td> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="40%%"> U Engine</td> </tr> <tr> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="20%%"> A</td> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="40%%"> 126 mm (4.96in.)</td> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="40%%"> 94 mm (3.70in.)</td> </tr> <tr> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="20%%"> B</td> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="40%%"> 126 mm (4.96in.)</td> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="40%%"> 108 mm (4.25in.)</td> </tr> <tr> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="20%%"> C</td> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="40%%"> 94 mm (3.70in.)</td> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="40%%"> 94 mm (3.70in.)</td> </tr> <tr> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="20%%"> D</td> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="40%%"> 94 mm (3.70in.)</td> <td align="center" colspan="1" rowspan="1" style="border:solid 1pt gray;" valign="middle" width="40%%"> 94 mm (3.70in.)</td> </tr> </tbody> </table>

 1 copy.jpg   36.2К   8 Количество загрузок: </td> </tr> </tbody></table><table border="0" cellpadding="0" cellspacing="0" style="width:100%;padding-bottom:6;"> <tbody> <tr> <td style="padding-left:3px;" valign="top" width="12"> 2.</td> <td style="padding-left:3px;" valign="top">
Install in the reverse order of removal, and note these items. <table border="0" cellpadding="0" cellspacing="1" width="100%"> <tbody> <tr> <td align="right" style="width:15px;" valign="top"> A.</td> <td style="padding-left:3px;" valign="top">
If you're installing a new compressor, drain all the refrigerant oil from the removed compressor, and measure its volume, Subtract the volume of drained oil from 120cc(4.20 oz.) the result is the amount of oil you should drain from the new compressor (through the suction fitting). </td> </tr> </tbody> </table> <table border="0" cellpadding="0" cellspacing="1" width="100%"> <tbody> <tr> <td align="right" style="width:15px;" valign="top"> B.</td> <td style="padding-left:3px;" valign="top">
Replace the O-rings with new ones at each fitting, and apply a thin coat of refrigerant oil before installing them. Be sure to use the right O-rings for R-134a to avoid leakage. </td> </tr> </tbody> </table> <table border="0" cellpadding="0" cellspacing="1" width="100%"> <tbody> <tr> <td align="right" style="width:15px;" valign="top"> C.</td> <td style="padding-left:3px;" valign="top">
To avoid contamination, do not return the oil to the container once dispensed, and never mix it with other refrigerant oils. </td> </tr> </tbody> </table> <table border="0" cellpadding="0" cellspacing="1" width="100%"> <tbody> <tr> <td align="right" style="width:15px;" valign="top"> D.</td> <td style="padding-left:3px;" valign="top">
Immediately after using the oil, replace the cap on the container and seal it to avoid moisture absorption. </td> </tr> </tbody> </table> <table border="0" cellpadding="0" cellspacing="1" width="100%"> <tbody> <tr> <td align="right" style="width:15px;" valign="top"> E.</td> <td style="padding-left:3px;" valign="top">
Do not spill the refrigerant oil on the vehicle; it may damage the paint; if the refrigerant oil contacts the paint, wash it off immediately. </td> </tr> </tbody> </table> <table border="0" cellpadding="0" cellspacing="1" width="100%"> <tbody> <tr> <td align="right" style="width:15px;" valign="top"> F.</td> <td style="padding-left:3px;" valign="top">
Adjust the drive belt. (Refer to HA-15) </td> </tr> </tbody> </table> <table border="0" cellpadding="0" cellspacing="1" width="100%"> <tbody> <tr> <td align="right" style="width:15px;" valign="top"> G.</td> <td style="padding-left:3px;" valign="top">
Charge the system and test its performance. (Refer to HA-10) </td> </tr> </tbody> </table> </td> </tr> </tbody></table>