Replacement 1. Loosen the wheel nuts(B) slightly. Raise the vehicle, and make sure it is securely supported. 2. Remove the front wheel and tire(A) from front hub . Kia Cerato TD 2009-2013 - замена шруса.jpg 20.67К 8 Количество загрузок: Be careful not to damage to the hub bolts (B) when removing the front wheel and tire (A). 3. Unstake the driveshaft lock nut using a chisel and hammer. Kia Cerato TD 2009-2013 - замена шруса (1).jpg 28.96К 9 Количество загрузок: Kia Cerato TD 2009-2013 - замена шруса (2).jpg 23.71К 6 Количество загрузок: 4. Remove driveshaft nut(B) from the front hub under applying the break. Tightening torque: 196.1~274.5N.m(20.0~28.0Kgf.m, 144.6~202.5lb.ft) Kia Cerato TD 2009-2013 - замена шруса (3).jpg 31.1К 7 Количество загрузок: 5. Remove the brake caliper mounting bolts (A), and then place the brake caliper assembly (B) with wire. Tightening torque: 80~100 N.m (8.0~10.0 Kgf.m, 58~72.3lb.ft) Kia Cerato TD 2009-2013 - замена шруса (4).jpg 31.46К 8 Количество загрузок:
#1
Отправлено 19 November 2012 - 15:54
Центр кузовного ремонта в Москве: kuzovnoi.center
Все, кто хочет получить скидку на ремонт - пишут в личку KRIONIKe
#2 Re: шрус (привод)
Отправлено 19 November 2012 - 15:59
6.
Remove the tie rod end ball joint from the knuckle.
(1)
Remove the split pin(A).
(2)
Remove the castle nut(B).
(3)
Disconnect the ball joint© from knuckle using the special tool (09568-4A000).
Tightening torque:
23~32 N.m (2.4~3.4 Kgf.m, 17~25 lb.ft)
Kia Cerato TD 2009-2013 - замена шруса (5).jpg 27.96К
6 Количество загрузок:
Apply a few drops of oil to the special tool. (Boot contact part)
7.
Remove the wheel speed sensor(B).
Tightening torque:
6.8~10.8N.m( 0.7~1.1Kgf.m,5.1~7.9lb.ft)
Kia Cerato TD 2009-2013 - замена шруса (6).jpg 34.83К
8 Количество загрузок:
8.
Remove the lower arm from the knuckle.
(1)
Remove the split pin(A).
(2)
Remove the castle nut(B).
(3)
Disconnect the lower amr© from knuckle using the special tool (09568-4A000).
Kia Cerato TD 2009-2013 - замена шруса (7).jpg 25.79К
9 Количество загрузок:
Be careful not to damage the boot and rotor teeth.
9.
Disconnect the driveshaft (A) from the front hub assembly.
Kia Cerato TD 2009-2013 - замена шруса (8).jpg 28.89К
8 Количество загрузок:
10.
Insert a pry bar between the transaxle case and joint case(A), and separate the drive shaft from the transaxle case.
Kia Cerato TD 2009-2013 - замена шруса (9).jpg 44.59К
7 Количество загрузок:
11.
Install in the reverse order of removal.
•
Use a pry bar(A) being careful not to damage the transaxle and joint.
•
Do not insert the pry bar(A) too deep, as this may cause damage to the oil seal.
•
Do not pull the driveshaft by excessive force it may cause components inside the joint kit to dislodge resulting in a torn boot or a damaged bearing.
•
Plug the hole of the transaxle case with the oil seal cap to prevent contamination.
•
Support the driveshaft properly.
•
Replace the retainer ring whenever the driveshaft is removed from the transaxle case.
Центр кузовного ремонта в Москве: kuzovnoi.center
Все, кто хочет получить скидку на ремонт - пишут в личку KRIONIKe
Последние обсуждения по киа церато 2 td на MyKia.club
Киа Церато 2 TD
Тех. вопросы →
Киа Церато клуб →
Кузов и Салон Kia Cerato →
заглушка двериАвтор Вячеслав 58.RU, 14 Dec 2015 |
|
|||
Киа Церато 2 TD
Тех. вопросы →
Киа Церато клуб →
Двигатель и КПП Kia Cerato →
насос ГУРАвтор *Гость* , 10 Aug 2015 |
|
|
||
Киа Церато 2 TD
Тех. вопросы →
Киа Церато клуб →
Электрика и Аудио Kia Cerato →
блок BCMАвтор krionika, 02 Jun 2011 |
|
|||
|
Киа Церато 2 TD
Тех. вопросы →
Киа Церато клуб →
Двигатель и КПП Kia Cerato →
характеристики двигателяАвтор krionika, 13 Dec 2010 |
|
||
Киа Церато 2 TD
Тех. вопросы →
Киа Церато клуб →
Двигатель и КПП Kia Cerato →
бензобакАвтор krionika, 04 Jul 2010 |
|