Сообщений в теме: 2

[getAway]

Kia Cerato LD (2004-2009) - снятие и установка радиатора кондиционера

REPLACEMENT 1. Recover the refrigerant with a recovery/recycling/charging station. 2. Drain the coolant. about 1? from the radiator. 3. Remove the nuts(A), then disconnect the discharge line and condenser line from the condenser. Plug or cap the lines immediately after disconnecting them to avoid moisture and dust contamination.  1 copy.jpg   30.95К   8 Количество загрузок: 4. Remove the condenser fan (Refer to the condenser fan). 5. Disconnect the upper hose(B) from the radiator(A).  2 copy.jpg   39.27К   7 Количество загрузок: 6. Remove the radiator fan. 7. Remove the bolts(A), then remove the upper mount brackets(B) from the radiator.  3 copy.jpg   31.53К   13 Количество загрузок: 8. Remove the bolts(A), then remove the condenser (B) by lifting it up. Be careful not to damage the radiator and condenser fins when removing the condenser.  4 copy.jpg   43.19К   12 Количество загрузок: 9. Install in the reverse order of removal, and note these items : A. If you're installing a new condenser, add refrigerant oil ND-OIL8. B. Replace the O-rings with new ones at each fitting, and apply a thin coat of refrigerant oil before installing them. Be sure to use the right O-rings for R-134a to avoid leakage. C. Be careful not to damage the radiator and condenser fins when installing the condenser. D. Be sure to install the lower mount cushions of condenser securely into the holes. E. Charge the system, and test its performance.

[getAway]

Kia Cerato LD (2004-2009) - снятие и установка компрессора кондиционера

REMOVAL 1. If the compressor is marginally operable, run the engine at idle speed, and let the air conditioning work for a few minutes, then shut the engine off. 2. Disconnect the negative cable from the battery. 3. Recover the refrigerant with a recovery/charging station (Refer to HA-8). 4. Loosen the drive belt (Refer to HA-14). 5. Remove the bolts, then disconnect the suction line and discharge line from the compressor. Plug or cap the lines immediately after disconnecting them to avoid moisture and dust contamination. 6. Disconnect the compressor clutch connector (A), and then remove 4 mounting bolts and the compressor.  1 copy.jpg   45.37К   20 Количество загрузок:

[getAway]

INSTALLATION
1.
Make sure of the length of compressor mounting bolts, and then tighten it A?B?C?D order.

 1 copy.jpg   45.26К   12 Количество загрузок:
Tightening torque : 2.0 ~ 2.5 kgf.m (19.6 ~ 24.5 N.m, 14.5 ~ 18.1 lbf.ft)
2.
Install in the reverse order of removal, and note these items.
A.
If you're installing a new compressor, drain all the refrigerant oil from the removed compressor, and measure its volume, Subtract the volume of drained oil from 120cc(4.20 oz.) the result is the amount of oil you should drain from the new compressor (through the suction fitting).
B.
Replace the O-rings with new ones at each fitting, and apply a thin coat of refrigerant oil before installing them. Be sure to use the right O-rings for R-134a to avoid leakage.
C.
To avoid contamination, do not return the oil to the container once dispensed, and never mix it with other refrigerant oils.
D.
Immediately after using the oil, replace the cap on the container and seal it to avoid moisture absorption.
E.
Do not spill the refrigerant oil on the vehicle; it may damage the paint; if the refrigerant oil contacts the paint, wash it off immediately.
F.
Adjust the drive belt (Refer to HA-14)
G.
Charge the system and test its performance. (Refer to HA-9)